This thesis has been conducted at Saab Bofors Dynamics AB. The purpose was to investigate if a non-linear missile model could be stabilized when the optimal control signal is computed considering constraints on the control input. This is particularly interesting because the missile is controlled with rudders that have physical bounds. This strategy is called Model predictive control. Simulations are conducted to compare this strategy with others; firstly simulations with step responses and secondly simulations when the missile is supposed to hit a moving target.

The control of indoor temperature must be able to handle large time constants and both measureable disturbances like outdoor temperature, and non-measurable disturbances, like waste heat from appliances. Due to cheaper microcontrollers (small computers with designated tasks) with better performance, more advanced and computation-demanding methods for control can be used.In this thesis, Generalized Predictive Control (GPC) has been implemented and tested on a theoretically derived model of a house. GPC states that a model of the system is estimated in every sample, and the control is carried out simultaneously, based on predictions of the model. Disturbances like solar radiation can be estimated and used in the control as well. The control signals are determined by quadratic programming, which makes it possible to consider conditions, for example limitations on the control signals.GPC requires a number of parameters to be defined, like model order and control signal penalty, but is relatively robust for variations in them.

In industrial control systems PID-control remains the prevalent strategy, also for processes that would benefit from model based control. The purpose of this thesis is to evaluate whether model based control can be readily implemented in an industrial control system. To this end a simulated surge tank with a simulated industrial control system is studied. For evaluation two scenarios with specified objectives are selected.Following a review of LQR and versions of MPC, Predictive Functional Control (PFC) is considered the most suitable for implementation. PFC is a form of MPC developed with industrial applications in mind and therefore has several advantages for implementation in an industrial control system.

The purpose with this masters thesis was to model the scanner in a system for laser bathymetry. The model was then used to develop a controller for the scanner so a good search pattern was achieved. Two different types of models have been tested, a physical model and a Black Box model of Box Jenkins type. The physical model has been derived from Lagranges equations. Identification experiments have been used to compute the Black Box model and to find the unknown parameters in the physical model.

In the pulp industry, digesters are used to disolve lignin in wood chips. The concentration of lignin is measured and is called the Kappa number. In this thesis, the question of whether an online Kappa sensor, taking samples from the mid-phase of the digester, is useful or not is analyzed. For the samples to be useful, there has to be a relationship between the measured Kappa at the mid- phase and the measured Kappa in the blowpipe at the bottom of the digester. An ARX model of the lower part of the digester has been estimated.

This thesis studies the negative impact that control signal saturation may have on a controlled system. Different methods that are used to compensate for this problem are also studied and evaluated. Both sensitivity to disturbances and the effect the method has on the systems'ability to follow a reference signal will be examined. Stability will be discussed, but no conclusions whether the systems are stabilized or not can be drawn. Control signal saturation will lead to a slower behavior in general.

Arbetet har utförts på Saab Bofors Dynamics AB i Linköping och dess syfte är att undersöka möjligheten att applicera teorin för prediktionsreglering, Model predictive control (MPC), på guidance systemet i en missil av typen Medium Range Air-to-Air Missiles (MRAAM). Även implementering via Explicit MPC har undersökts. I tidigare studier har det visat sig att den moderna slutfasstyrningsalgoritmen Linear Quadratic Augmented Proportional Navigation (LQAPN), som återkopplar missilens acceleration och rotation, uppvisar en bättre prestanda än de mer klassiska styrlagarna. Det främsta intresset med denna studie är därför att undersöka hur tillvida en styrlag baserad på MPC kan mäata sig med dessa resultat. Fördelen med att använda MPC är framförallt att man kan ta hänsyn till styrsignalbegränsningar på ett direkt och intuitivt sätt.

This master?s thesis describes the development of a model of the catalystsystem aiming at control by an MPC. A well functioning model, which is suitable in control purpose, is important while emission legislation become more and more hard to fulfill for the car manufacturers. Much research has been done in the field of physical modeling of the system, but in this work a linear adaptive time discrete ARX-model is developed and validated.The systems tendency to change its dynamic during usage implies that the model must be adaptive. The developed model proved to be well functioning and shows promising conditions for the MPC design.

This is a final thesis done at BT, considering one of their forklift truck models called Reflex. The first part of this report is about a preliminary investigation investigating what kind of diagnostic systems BTwants to use, and also which demands there are to meet all expectations on such system. Secondly a diagnostic system, which will show if the drive wheel is worn out, will be presented. In the preliminary investigation, two kinds of diagnostic systems were mentioned. These were Model based diagnosis and Predictive analysis.

This master thesis deals with problems in the arc length control in Pulsed MIG/MAG Welding. The main problem is that it is not possible to measure the arc length. In the present solution the voltage over both the electrode and the arc represents the arc length. To improve the arc length control a model of the electrode melting has been built. One output from the model is the voltage over the electrode and with this voltage together with the measured voltage it is possible to calculate the voltage over just the arc.

When a helicopter is flying, the dynamics vary depending on, for example, speed and position. Hence, a time-invariant linear model cannot describe its properties under all flight conditions. It is therefore desirable to update the linear helicopter model continuously during the flight. In this thesis, two different recursive estimation methods are presented, LMS (Least Mean Square) and adaptation with a Kalman filter. The main purpose of the system estimation is to get a model which can be used for feedback control.

Modern air battles are very dynamic and fast, and put extreme pressure on pilots. In some unpredictable situations, like new discovered threats or mission plan deviation because of enemy aircraft, the pilots might need to replan their predefined flight route. This is very difficult, if not impossible, to do since numerous factors affect it. A system that can help the pilots to do such a thing is needed. Previous work in this field has involved methods from artificial intelligence like A*-search.

Our purpose with this qualitative study is to investigate how teachers experience their work situation, using Karasek and Theorell?s demand-, control- and support model. The study is based upon ten semi-structured interviews with gymnasium teachers. The interviews were transcribed and coded with three different themes; demand, control and support. We analyzed the results with Karasek and Theorell?s mentioned model.

This study examines if the prediction of cardiovascular disease in hypertensive patients can be improved upon when renal function and microalbuminuria are added to the classical risk factors The predictive capability of a model is measured by discrimination, calibration, reclassification and Harrell's C.The results are ambigious. In most cases, microalbuminuria should be included in the model, but the results regarding the other measures of renal function are varied. Therefore, the selection of risk factors to include in the model depends on which measure of prediction one prioritizes..

The aim is to develop a new decision-making model for credit-loans. The model will be specific for credit applicants of the OKQ8 bank, becauseit is based on data of earlier applicants of credit from the client (the bank). The final model is, in effect, functional enough to use informationabout a new applicant as input, and predict the outcome to either the good risk group or the bad risk group based on the applicant?s properties.The prediction may then lay the foundation for the decision to grant or deny credit loan.Because of the skewed distribution in the response variable, different sampling techniques are evaluated. These include oversampling with SMOTE, random undersampling and pure oversampling in the form of scalar weighting of the minority class.